Most drawings call out surface finish as “Ra 63” or “32 μin” — and most machinists know what that means. The problems start when the drawing uses Rz instead of Ra, when the callout doesn’t specify units (μin or μm), or when the finish requirement is unrealistically tight for the process being used. A drawing that says “Ra 4 μin” on a milled surface is asking for a grinding or polishing operation that may not be in the quote.
Quick Summary: Ra (arithmetic average roughness) is the most common surface finish parameter in the U.S. Rz (average maximum peak-to-valley height) is common on European and ISO-standard drawings. They measure different things and aren’t directly convertible — but as a rough rule of thumb, Rz runs 4–6x higher than Ra for typical machined surfaces. Specify the parameter (Ra or Rz), the value, the units (μin or μm), and which surfaces it applies to. If you only mark one surface, the machinist assumes everything else is standard “as-machined.”
What Do Ra and Rz Actually Measure?
| Parameter | What It Measures | Typical Machined Range | When to Use |
|---|---|---|---|
| Ra | Average deviation from the mean line over the sampling length | 16–125 μin (0.4–3.2 μm) for milling; 4–32 μin (0.1–0.8 μm) for grinding | Default for most U.S. aerospace drawings |
| Rz | Average of the 5 highest peak-to-valley distances within the sampling length | 4–6x the Ra value for the same surface | Common on European/ISO drawings; more sensitive to isolated deep scratches |
| Rmax (Ry) | Single largest peak-to-valley distance | Higher than Rz — captures worst-case defect | Used when a single scratch or gouge could cause a functional failure (sealing surfaces) |
Ra averages out the roughness profile, so a surface with one deep scratch and an otherwise smooth finish can still pass Ra but fail Rz. For sealing surfaces, O-ring grooves, and fatigue-critical areas, Rz or Rmax may be more appropriate — but Ra is still the default on most American aerospace drawings.
What Finish Can Each Process Achieve?
| Process | Typical Ra Range (μin) | Typical Ra Range (μm) |
|---|---|---|
| Rough milling | 125–250 | 3.2–6.3 |
| Finish milling | 32–63 | 0.8–1.6 |
| Finish turning | 16–63 | 0.4–1.6 |
| Surface grinding | 8–32 | 0.2–0.8 |
| Cylindrical grinding | 4–16 | 0.1–0.4 |
| Lapping / polishing | 1–4 | 0.025–0.1 |
| As-cast or as-forged | 250–1000 | 6.3–25 |
If the drawing calls out Ra 8 μin on a milled surface, the shop will need to add a grinding operation. That’s a separate setup, often on a different machine, and it adds cost. Make sure the finish requirement matches the actual functional need of the surface.
Frequently Asked Questions
What does “32 finish” mean without units? In the U.S., it almost always means Ra 32 μin (0.8 μm). But this is assumed, not specified. If the drawing doesn’t state units, add them. On international drawings, “32” could mean Ra 32 μm (which is a very rough surface) — an approximately 39x misinterpretation.
How do I convert between Ra μin and Ra μm? Divide μin by 39.37 to get μm. Ra 63 μin = Ra 1.6 μm. Ra 32 μin = Ra 0.8 μm. Ra 16 μin = Ra 0.4 μm.
Does surface finish affect fatigue life? Yes. Rougher surfaces have more stress-concentration points that can initiate fatigue cracks. For fatigue-critical aerospace components, a smoother finish (Ra 16–32 μin or better) on loaded surfaces is standard practice.
Written by James Wright, CEO of Accurate Machine & Tool.
Sources
[1] eMachineShop — GD&T and drawing specification resources, emachineshop.com
[2] ASME B46.1 — Surface Texture (Surface Roughness, Waviness, and Lay)
[3] Machinery’s Handbook, 32nd Edition — surface finish by process (Industrial Press)